Wdsen Electronic Technology Co., Ltd

iButton Temperature Loggers

iButton Hygrochron Temperature/Humidity Logger

Main Content

iButton Temperature Loggers DS1921G DS1922 DS1923

iButton Hygrochron Temperature Humidity Loggers

DS9097U-009, DS9097U-E25, DS9097U-S09

Universal 1-Wire COM Port Adapte

DS9097 COM Port Adapter
DS9097E COM Port Adapter
DS9097U-009 Universal 1-Wire COM Port Adapter
DS9097U-E25 Universal 1-Wire COM Port Adapter
DS9097U-S09 Universal 1-Wire COM Port Adapter

DS9097U-009, DS9097U-E25, DS9097U-S09

Universal 1-Wire COM Port Adapter

Description

The DS9097U is a sophisticated RS-232 to 1-Wire® adapter, which performs RS-232 level conversion and actively generates the 1-Wire communication signals. Together with an adequate software driver, it enables a Windows®-based PC to directly communicate with any 1-Wire device connected to the adapter's RJ11 port. The DB9 version reads and writes any non-EPROM 1-Wire device. To write to EPROM devices, the DB25 version with external power supply is required. For a list of suitable 1-Wire network cables, refer to the Connectivity Matrix table in the DS1402x 1-Wire network cables data sheet.

All DS9097U adapters are based on the DS2480B serial 1-Wire line driver chip. The RXD/TXD polarity select input of the DS2480B is connected to VDD (noninverting).
The DS9097U communicates with 1-Wire devices at standard speed as well as overdrive speed. The serial port must support a data transmission rate of 9600bps. Under software control, the adapter can be set up for RS-232 data rates of 19200bps, 57600bps, and 115200bps. The two higher rates are recommended for communication at overdrive speed with overdrive-capable devices. Since the DS9097U operates in a byte mode, every data byte received from the RS-232 port generates eight time slots on the 1-Wire line.

Note that there are some COM ports that use signal levels of less than (±) 5V. The DB9 versions of this adapter do not work with such ports. The DS9097U-E25 adapter, however, functions in most cases if external power is supplied. Without EPROM programming, the external power can be anywhere in the range of 6V to 9V. For EPROM programming the voltage must be at 12V in any case. Before using an externally powered DS9097U-E25 with a COM port of less than (±) 5V, check whether the COM port will not be damaged by 5V on its RXD input.

Key Features

  • True-Ground Interface to an RS-232 COM Port for Reading and Writing 1-Wire Devices
  • Works with Bipolar as well as Unipolar Logic Signals
  • Compatible to COM port of (±)5V to (±)12V (DB9 Version Only) or (±)6V to (±)12V (DB25 Version)
  • Supports Reading and Writing at Standard and Overdrive Speeds
  • Provides Strong Pullup to 5V for Temperature and EEPROM 1-Wire Devices
  • Programs 1-Wire EPROM Devices (DB-25 Version with External 12V Power Supply Only)
  • Communicates at Data Rates of 9.6kbps (default), 19.2kbps, 57.6kbps, and 115.2kbps
  • Standard DB9 or DB25 Female Connector and 6-Lead RJ11 Connector for Easy Attachment of Standard 1-Wire Cables and Probes
  • Includes DS2502 Identification Chip (DS9097U-009 Only)

 

 

DS1921G Thermochron iButton Device

DS1921H High-Resolution Thermochron iButton Devices

DS1921Z High-Resolution Thermochron iButton Devices

DS1922E iButton High-Temperature Logger with 8KB Data-Log Memory

DS1922L iButton Temperature Loggers with 8KB Data-Log Memory

DS1922T iButton Temperature Loggers with 8KB Data-Log Memory

DS1923 iButton Hygrochron Temperature/Humidity Logger with 8KB Data-Log Memory

DS1925 iButton High-Density Temperature Logger with 122KB Data-Log Memory

DS9097U-S09 Universal 1-Wire COM Port Adapter

DS1402D-DR8 1-Wire Network Cables

 

 

 

DS1921G

Thermochron iButton Device

DS1922L

iButton Temperature Loggers with 8KB Data-Log Memory

DS1923

iButton Hygrochron Temperature/Humidity Logger with 8KB Data-Log Memory

DS1922T

iButton Temperature Loggers with 8KB Data-Log Memory